EAN: 4001869324548 - manufacturer-number: 5WG1120-1AB02 - Band suppressor/choke for bus system Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 2, Choke N 120/02, 640 mA The operating voltage for the bus devices supplied through the bus is transmitted via the same twisted pair cable as the data telegrams. The N 120/02 choke prevents the 29V power-supply from short-circuiting the data telegram on the bus line. The choke receives the power via the low-voltage connector (yellow-white) on the front side. This power is directly connected to the two outer printed conductors of the data rail. It is fed via inductors to the two inner printed conductors of the data rail and to the bus connector terminal (black-red) on the front side of the device. The 29Vsupply voltage fed to the low-voltage connector (yellow-white) may be sourced from a power supply unit N125/21. It may also be sourced from a power supply N123 via the data rail. Via the built-in reset-switch (operation > 10 s) the bus devices are set to their default setting, i.e. the bus de-vices return to their default setting with the recurring supply voltage. This is done by short-circuiting the bus line and switching off the supply voltage. To the DC29V supply voltage the choke resistance is low. The informations will be send via the instabus EIB as an alternating current. For it the resis-tance of the choke N 120/02 is high- resistance and there-fore the operating voltage does not significantly affect the information signal. Technical Specifications Input voltage: rated voltage: DC 29 V (DC 28...30V), rated current: 640 mA, Operator elements 1 slide switch for re-setting the bus devices connected to the line (operation > 10 s), Display elements 1 red LED for indicating when the slide switch is set to reset-position, Connections: power supply: pressure contacts on data rail (outer printed conductors) and screwless extra low-voltage terminal (yellow-white) 0.6...0.8mm solid single-core copper wire, bus line: pressure contacts on data rail (inner printed conductors) and crewless extra low-voltage terminal (black-red) 0.6...0.8mm solid single-core copper wire, Physical specifications: housing: plastic, N-system DIN-rail mounted device, width: 2 SUs (1 SU = 18 mm) weight: approx. 105 g, fire load: approx. 1470 kJ ± 10 %, installation: rapid mounting on DIN EN 50022-35 x 7,5 rail, Electrical safety: degree of pollution (according to IEC 60664-1) :2, protection (according to EN 60529): IP 20, protection class (according to IEC 61140): III, overvoltage class (according to IEC 60664-1): III, bus: safety extra low voltage SELV DC 24 V, device complies with EN 50090-2-2, Reliability rate of failure: 82 fit at 45 °C, Electromagnetic compatibility complies with EN 61000-6-2, EN 50090-2-2 and EN 61000-6-3, Environmental specifications: climatic conditions: EN 50090-2-2, ambient temperature operating: - 5 ... + 45 °C, storage temperature: - 25 ... + 70 ° C, relative humidity (non- condensing): 5 % to 93 %, Certification EIB certificate CE norm complies with the EMC regulations (residential and functional buildings), and low voltage regulations Manufacturer: SIEMENS Manufacturer No.: 5WG1 120-1AB02 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1120-1AB02

EAN: 4001869355900 - manufacturer-number: 5WG1258-1AB02 - Temperature sensor for bus system Bus system EIB/KNX, Model Temperature sensor, Mounting method Surface mounted (plaster), Bus connection included, Colour Other, Binary input, Degree of protection (IP) IP20, Temperature Sensor N 258/02 The temperature sensor N 258/02 is a device with a width of 4 module units for DIN rail mounting, with 4 inputs for the direct connection of one Pt1000 temperature sensor per input via a two-core cable up to 50 m long. The device is supplied by mains voltage. It enables the recording and monitoring of up to 4 temperatures in the range -35...+145°C. The temperature is measured cyclically per measurement channel (with a fixed cyclic period of 1 s). It can be set via the ETS whether the measured value should be filtered by meanvalue generation, whether it should be send cyclically or eventdriven after a change by an adjustable differential value and whether it should be monitored for a lower and/or upper limit value. It is ensured via an adjustable hysteresies that a measured value that fluctuates by the limit value does not lead to a continuous violation of the limit value with a corresponding message. Technical data Power supply: -Bus voltage carried out via the bus line, -N 258/02 electronics: intergrated power supply unit 230V AC, +10%/-15%, 50Hz power consumption: 2.5 W, -Supply voltage for bus: 21V DC to 30V DC, Inputs/outputs: -Mains connection: 2 pole (N,L), -4 inputs for the connection of one Pt1000 temperature sensor each in 2-conductor technology, max. cable range: 50m, measuring range: -35...+145°C, measured value resolution: 0.1K in the range +5...+45°C and 0,25K in all other ranges Manufacturer: Siemens Manufacturer-No.: 5WG1 258-1AB02 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1258-1AB02

Communicatiemodule voor communicatie tussen verschillende LOGO!'s. Voor het aansluiten van instabus EIB-Sensorik en Aktorik op LOGO! (bijv. weerstation). Klik verder voor meer info.

Communicatiemodule voor communicatie tussen verschillende LOGO!'s. Voor het aansluiten van instabus EIB-Sensorik en Aktorik op LOGO! (bijv. weerstation). Klik verder voor meer info.

manufacturer-number: 5WG1305-1AB01 - The N 305 scene/event controller offers unbeatable flexibility and performance with 8 scenes of 8 tasks each or 8 event programs with 10 tasks, 1-bit and 8-bit scenes, comparison operators, and dynamic comparison values. It can also handle all data types. Szenen-/Ereignisbaustein N 305 Mit dem N 305-Baustein kann der Anwender bis zu acht unterschiedliche Szenen oder acht Ereignisprogramme aufrufen wie beispielsweise „Vortrag oder Zentral Aus, die den Raum oder das Gebäude in einen vordefinierten Zustand versetzen. Dazu zählen das Ein- und Ausschalten sowie Dimmen von Lichtquellen sowie die Regulierung der Heizung. Temperaturmesser oder beliebige andere Sensoren und Ereignisse können die jeweiligen Programme auslösen. N 305 Szenen- / Ereignisbaustein, mit 1-bit- oder 8-bit-Szenensteuerung zum Speichern und Abrufen von bis zu acht Szenen mit bis zu acht Kommunikationsobjekten pro Szene, mit folgenden zulässigen Datentypen der Kommunikationsobjekte: 1-Bit-Schalten / -Jalousie / -Szene, 2-Bit-Zwangsführung, 8-Bit-Szene / -Wert / -Zählwert / -ASCII- Zeichen, 2- / 4-Byte Gleitkomma- und -Zählwert, 6-Byte-Störungsinformation, 14-Byte-Zeichenkette, mit Vorbelegung des gewünschten Zustands / Wertes pro Komm.-Objekt und Szene über die ETS (Engineering Tool Software), mit vom Benutzer und auch zur Laufzeit änderbaren und im Szenen-/Ereignisbaustein speicherbaren Szenen, mit Erhalt der gespeicherten Werte auch bei Busspannungsausfall, mit Abrufen und Speichern von Szenen über 1-Bit- oder über 8-Bit-Szenentelegramme, mit wählbarem Umsetzen von 1-Bit- auf 8-Bit-Szenenauslösung und umgekehrt, mit im Bereich von 0 bis 30 Minuten einstellbarem verzögertem Senden der Telegramme bei Aufruf einer Szene, mit 8 Ereignisprogrammen mit jeweils bis zu 10 Aufträgen, mit folgenden Datentypen für die Ereignisauslösung: 1-Bit-Schalten, 2-Bit-Zwangsführung, 4-Bit-Wert, 8 Bit-Wert, 2- / 4-Byte-Gleitkomma- und -Zählwert, 3-Byte-Uhrzeit, 6-Byte-Störungsinformation, 8-Byte-Systemzeit mit folgenden Datentypen für Ereignisaufträge: 1-Bit-Schalten / -Jalousie / -Szene, 2-Bit-Zwangsführung, 4-Bit-Dimmen, 8-Bit-Wert / -Zählwert / -ASCII-Zeichen / -Szene, 2- / 4-Byte Gleitkomma- und Zählwert, 6-Byte Störungsinformationen, 14-Byte-Zeichenketten, mit Einstellen der gewünschten Vergleichswerte und Auslösebedingungen in den Ereignisprogrammen über die ETS, mit Freigabe und Verriegelung der Ereignisprogramme, mit einstellbarer Sendeverzögerung der Ereignistelegramme nach Aufruf eines Ereignisprogramms im Bereich von 0 bis 120 Minuten, mit LED zur Anzeige des Betriebsstatus, mit integriertem Busankoppler,- Norm B: 223/108/03441, mit Busanschluss über Busklemme und über Kontaktsystem zur Datenschiene, Breite 1 TE (1 TE = 18 mm), Gewicht 0,065 kg Hersteller: Siemens Art.-Nr.: 5WG1 305-1AB01 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1305-1AB01

EAN: 4010337009559 - manufacturer-number: 101900 - Light control unit for bus system 3-ch Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 4, Bus connection included, Local operation/hand operation, With LED indication, Interface 1-10 V, Max. switching current (resistive load) 16A, Max. switching power 2500W, Number of outputs 3, Degree of protection (IP) IP20, Blueway-Classification Component for energy saving solution, Three-channel 1-10 V control unit compact The control unit receives telegrams via the instabus EIB and switches or dims fluorescent lamps in conjunction with electronic ballasts. During the dimming process, the electronic ballasts are controlled via a 1-10 V interface. The switching function is ensured by a relay contact switching the supply voltage to the electronic ballasts. The relay contact can also be actuated manually without affecting the bus. Technical data External supply --- Supply of instabus EIB voltage: 21 – 32 V DC SELV power consumption max. 240 mW (I = 10 mA) connection: instabus connecting and branch terminal Input number: 3 signal voltage: 1-10 V signal current: max. 100 mA per channel (1 Insta electronic ballast approx. 0.8 mA, 1 Siemens electronic ballast: approx. 1 mA, 1 Helvar electronic ballast: approx. 4 mA) signal duration: continuous connection: screw-type terminals: 0.5 – 4 mm² single wire and stranded without ferrule 0.5 – 2.5 mm² stranded with ferrule length of input line: max. 500 m bei 0.5 mm²Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 101900

EAN: 4001869333557 - manufacturer-number: 5WG1258-2AB21 - Movement sensor for bus system 0...360° Bus system EIB/KNX, Other bus systems None, Model Presence detector, Mounting method Flush mounted (plaster), Max. transmission range sideways 11m, Detection angle vertical from/to 0 ... 120°, Detection angle horizontal from/to 0 ... 360°, Blueway-Classification Component for energy saving solution, Presence detector FM 258/21 Passive infrared presence detector for indoor use, type of protection IP 20, for mounting on the ceiling, Fresnel lenses in a pyramid arrangement, horizontal detection range 360°, vertical range approx. 120°, from approx. 3 x 3 m to approx. 8 x 8 m, dependent on mounting height or room height Capability characteristics: passive infrared presence detector for EIB, square 360° sensing range for ceiling mounting, control of one or two lighting groups, switching or constant light control, mixed light measurement, lightning control fully or semi-automatic as required, presence output with ON/OFF delay, monitoring output with cyclic message object, output for brightness (LUX), integrated scene module with 2 scenes, can be parameterized remotely using ETS, parallel operation of several presence detectors (master-slave, master-master) without logic module, with integrated bus coupling, Dimensions: 102 x102 x 33 mm Manufacturer: SIEMENS Manufacturer No.: 5WG1 258-2AB21 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1258-2AB21

EAN: 4001869317878 - manufacturer-number: 5WG1262-1EB01 - Binary input for bus system 8-ch Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 6, Bus connection included, Number of inputs 8, Primary voltage range 0V, Generates signal voltage, Binary input N 262E01, 8x potential-free contact Binary input device N 262E01 with 8 inputs for potential-free contacts, with a length of unshielded connecting cable per input of max. 100 m, with an integrated power supply for AC 230 V to supply the electronics, with 1 green LED for displaying the 230 V operating voltage, with 1 red LED per binary input for status display, with a function to be selected and assigned per input: Switching status / binary value transmission, Switching, edge-triggered, Switching, short / long operation, 1-button dimming, 1-button solar protection control, 1-button group control (sequence control), 1-bit Scene control, 8-bit Scene control, 8-bit value, edge-triggered, 8-bit value, short / long operation, 16-bit floating point value, edge-triggered, 16-bit floating point value, short / long operation, 8-bit pulse counting without threshold check, 8-bit pulse counting with threshold check, 16-bit pulse counting without threshold check, 16-bit pulse counting with threshold check, 32-bit pulse counting without threshold check, 32-bit pulse counting with threshold check, respectively with a function to be assigned to a pair of inputs: 2-button dimming with stop telegram or 2-button solar protection control, with selectable blocking / releasing of each input by a blocking object, with sending of the input objects after a change of status, with selectable cyclical sending of the input objects, with integrated bus coupling unit with only half a standard bus load, with connection to the bus line either via the bus terminal or via the contact system to the data rail, as device in N-System dimensions with snap-on mounting on a DIN rail EN 60715-TH35-7.5, max. width 6 MU (1 Module Unit = 18 mm) Manufacturer: Siemens Order nr.: 5WG1 262-1EB01 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1262-1EB01

EAN: 4001869317854 - manufacturer-number: 5WG1262-1EB11 - Binary input for bus system 16-ch Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 6, Bus connection included, Number of inputs 16, Primary voltage range 0V, Generates signal voltage, Binary input N 262E11, 16x potential-free contact Binary input device N 262E11 with 16 inputs for potential-free contacts, with a length of unshielded connecting cable per input of max. 100 m, with an integrated power supply for AC 230 V to supply the electronics, with 1 green LED for displaying the 230 V operating voltage, with 1 red LED per binary input for status display, with a function to be selected and assigned per input: Switching status / binary value transmission, Switching, edge-triggered, Switching, short / long operation, 1-button dimming, 1-button solar protection control, 1-button group control (sequence control), 1-bit Scene control, 8-bit Scene control, 8-bit value, edge-triggered, 8-bit value, short / long operation, 16-bit floating point value, edge-triggered, 16-bit floating point value, short / long operation, 8-bit pulse counting without threshold check, 8-bit pulse counting with threshold check, 16-bit pulse counting without threshold check, 16-bit pulse counting with threshold check, 32-bit pulse counting without threshold check, 32-bit pulse counting with threshold check, respectively with a function to be assigned to a pair of inputs: 2-button dimming with stop telegram or 2-button solar protection control, with selectable blocking / releasing of each input by a blocking object, with sending of the input objects after a change of status, with selectable cyclical sending of the input objects, with integrated bus coupling unit with only half a standard bus load, with connection to the bus line either via the bus terminal or via the contact system to the data rail, as device in N-System dimensions with snap-on mounting on a DIN rail EN 60715-TH35-7.5, max. width 6 MU (1 Module Unit = 18 mm) Manufacturer: Siemens Order nr.: 5WG1 262-1EB11 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1262-1EB11

EAN: 4001869317939 - manufacturer-number: 5WG1264-1EB11 - Binary input for bus system 16-ch Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 6, Bus connection included, Number of inputs 16, Primary voltage range 12 ... 230V, Generates signal voltage, Binary input N 264E11, 8x potential-free and 8x AC/DC 12...230 V contact Binary input device N 262E01 with 16 inputs: 8 for AC/DC voltages 12...230 V and 8 for potential-free contacts, with an integrated power supply for AC 230 V to supply the electronics, with 1 green LED for displaying the 230 V operating voltage, with 1 red LED per binary input for status display, with a function to be selected and assigned per input: Switching status / binary value transmission, Switching, edge-triggered, Switching, short / long operation, 1-button dimming, 1-button solar protection control, 1-button group control (sequence control), 1-bit Scene control, 8-bit Scene control, 8-bit value, edge-triggered, 8-bit value, short / long operation, 16-bit floating point value, edge-triggered, 16-bit floating point value, short / long operation, 8-bit pulse counting without threshold check, 8-bit pulse counting with threshold check, 16-bit pulse counting without threshold check, 16-bit pulse counting with threshold check, 32-bit pulse counting without threshold check, 32-bit pulse counting with threshold check, respectively with a function to be assigned to a pair of inputs: 2-button dimming with stop telegram or 2-button solar protection control, with selectable blocking / releasing of each input by a blocking object, with sending of the input objects after a change of status, with selectable cyclical sending of the input objects, with integrated bus coupling unit with only half a standard bus load, with connection to the bus line either via the bus terminal or via the contact system to the data rail, as device in N-System dimensions with snap-on mounting on a DIN rail EN 60715-TH35-7.5, max. width 6 MU (1 Module Unit = 18 mm) Manufacturer: Siemens Order nr.: 5WG1 264-1EB11 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1264-1EB11

EAN: 4001869384726 - manufacturer-number: 5WG1254-3EY02 - Multiple sensor for bus system Bus system EIB/KNX, Other bus systems None, Model Multiple sensor, Mounting method Surface mounted (plaster), Bus connection included, Colour White, Binary input, Degree of protection (IP) IP54, Kombisensor AP 254/02, zur Helligkeits- und Temperaturmessung Dual sensor AP 254/02 enables you to control Venetian blinds and lighting simultaneously. A solar protection channel automatically controls the solar protection equipment. There are 4 universal channels available for controlling of switch, dimming and Venetian blind actuators according to the ambient brightness and/or temeperature. Outside temperature and brightness are also detected and transmitted reliably. Measurement values for the temeperature range from - 25°C to + 55°C and for the brightness level from 1 to 100,000 lux. zum Erfassen und Übertragen von Helligkeit und Temperatur, Messbereich Temperatur -25 °C bis +55 °C, Messbereich Helligkeit 1 Lux bis 100 000 Lux, Erfassungswinkel horizontal -60° bis +60°, vertikal -35° ... +66,5°, zur Steuerung von Schalt-, Dimm- und Jalousieaktoren abhängig von der Umgebungshelligkeit und/oder Umgebungstemperatur, mit einem Sonnenschutzkanal zur automatischen Steuerung von Sonnenschutzeinrichtungen, mit Start und Stop der Automatik über ein Objekt oder eine Dämme-rungsschwelle, mit bis zu drei Helligkeitsschwellen zur Bestimmung der Höhe und Position der Jalousien bzw. Rolladen, mit optionalem Einlernen der Dämmerungsschwelle und der Helligkeitsschwellen über ein Einlernobjekt, mit Sperrobjekt zum vorübergehenden Deaktivieren der Funktion des Sonnenschutzkanals, mit bis zu vier Universalkanälen zur Steuerung von Schalt-, Dimm- und Jalousieaktoren in Abhängigkeit der Umgebungshelligkeit und / oder -temperatur, wahlweise mit Schwellwertschalter für Helligkeit, Schwellwertschalter für Temperatur oder Schwellwertschalter als logische Kombination von Helligkeit und Temperatur, mit optionalem Einlernen der Helligkeitsschwelle jedes Universalkanals über ein zugehöriges Einlernobjekt, mit möglicher Deaktivierung jedes Universalkanals über ein zugehöriges Sperrobjekt (1 Bit), mit optionalem zweiten Objekt zum Senden eines zweiten Telegramms bei Erfüllung der Schwellwertbedingung, - Norm B: 223/108/03441, mit Betrieb der Elektronik über Buspannung, mit integriertem Busankoppler, Busanschluss über Busklemme, zur Aufputz-Montage, Schutzart IP 54, 110 x 72 x 54 mm Hersteller: Siemens Art.-Nr.: 5WG1 254-3EY02 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1254-3EY02

EAN: 4001869377537 - manufacturer-number: 5WG1251-3AB11 - Movement sensor for bus system 0...290° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Surface mounted (plaster), Material Plastic, Material quality Thermoplastic, Surface treatment Other, Type of surface Brilliant, Colour White, RAL-number (akin) 9010, Staircase monitoring, Response value luminosity adjustable, Teach-function for response value luminosity, Max. transmission range sideways 8m, Max. transmission range frontally 8m, Detection angle horizontal from/to 0 ... 290°, Colour variant White, Blueway-Classification Component for energy saving solution, AP 251/11 Bewegungsmelder IP55, titanweiß UP 255/11 brightness controller has integrated, energy saving constant light control. Parallel to this, four additional light groups can also be dimmed with off-set. Calibration is quite simple, either per hand-held transmitter or via the bus. zum Erkennen und Melden von Bewegung, wahlweise ohne oder unter Berücksichtigung einer Helligkeits-Schwelle, mit Sensorwinkel 290°, einschließlich Abdeckblende zum Begrenzen des Erfassungsbereichs, Reichweite mindestens 16 m (Radius) bei Montagehöhe 2...4 m und 22 °C, mit integriertem Infrarot-Empfänger zum Einstellen von Helligkeitsschwelle und Nachlaufzeit sowie der Betriebsart (Testbetrieb, Standardbetrieb, Impulsbetrieb) über eine Infrarot-Fernbedienung, mit Sperren und Freigeben des Meldebetriebes über ein Kommunikationsobjekt, mit Spannungsversorgung der Elektronik über die Busspannung, mit integriertem Busankoppler, mit Busanschluss über Busklemme, als AP-Gerät zur Wand- oder Decken-Montage, mit Schutzart IP 55 zur Montage auch im Außenbereich, 180 mm x 86 mm x 74 (H x B x T) Technische Daten Sensor - Erfassungsbereich: 290° - Montagehöhe: 2 ... 4 m, ideal 2,50 m - Reichweite (Montagehöhe 2,50 m, +22 °C): ca. 16 m - Dämmerungssensor: 0,5 ... 2000 Lux - Nachlaufzeit : 5 Sekunden ... 30 Minuten - Impulsbetrieb 1 s EIN, 9 s AUS - Test-Modus: Helligkeitsunabhängiger Betrieb,Nachlaufzeit 2 s Spannungsversorgung - Busspannung: erfolgt über die Buslinie - Busstrom: 11 mA Bedienelemente - 1 Lerntaste: zum Umschalten Normalmodus / Adressiermodus - 2 Taster: zum lokalen Einstellen von Betriebsart, Helligkeits-Schaltschwelle  , ,und Nachlaufzeit des Bewegungsmelders,unabhängig vom Bus Anzeigeelemente - 1 rote LED: zur Kontrolle der Busspannung und zur Anzeige Normalmodus /  , ,Adressiermodus - 1 rote LED (unter der Linse des Bewegungsmelders): zur Quittierung bei  , ,Betriebsart- und Parameter-Einstellungen Anschlüsse - Busleitung: Busklemme schraubenlos, 0,6... 0,8 mm Ø eindrahtig,  , ,Abisolierlänge 5 mm Mechanische Daten - Gehäuse: Kunststoff - Abmessungen: ca. 180 mm x 86 mm x 74 mm(L x B x H) - Verstellbereich Schwenkarm: max. 120° - Norm B: 223/108/03441 - Gewicht: ca. 245 g - Brandlast: ca. 7500 kJ Elektrische Sicherheit - Verschmutzungsgrad (nach IEC 60664-1): 2 - Schutzart (nach EN 60529): IP 55 - Überspannungskategorie (nach IEC 60664-1): III - Bus: Sicherheitskleinspannung SELV DC 24 V - Gerät erfüllt: EN 50090-2-2 EMV-Anforderungen - erfüllt EN 50090-2-2 Umweltbedingungen - Klimabeständigkeit: EN 50090-2-2 - Umgebungstemperatur im Betrieb: - 30 ... + 50 °C - Lagertemperatur: - 25 ... + 70 °C - rel. Feuchte (nicht kondensierend): 5 % bis 93 % Prüfzeichen - KNX EIB CE-Kennzeichnung - gemäß EMV-Richtlinie (Wohn- und Zweckbau), Niederspannungsrichtlinie Hersteller: Siemens Art.-Nr.: 5WG1 251-3AB11 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1251-3AB11

EAN: 4013364047365 - manufacturer-number: BT24 - Surge protection for signal systems Nominal voltage DC 24V, Nominal discharge surge current (8/20) 5kA, Nominal load current 6A, Mounting method Connector/cable adapter, Connection 1 Other, Max. continuous voltage DC 45V, Voltage protection level core/core 1200V, Voltage protection level core/earth 650V, Signalling at the device None, Ueberspannungsschutz DEHN für den Überspannungsfeinschutz von instabus EIB Geräten. Der Überspannungsschutz wird entweder anstelle der Busklemme in das Busgerät eingesteckt oder direkt an die Busklemme der Busgerätes angeschlossen. Zur Überspannungsableitung wird der herausgeführte grüne Erdungsleiter am nächsten Erdungspunkt angeschlossen. Techn. Daten: Bemessungsspannung: DC 24 V Bemessungsstrom 6 A Bemessungsableitstoßstrom 5 kA Schutzpegel 350 V Anschlüsse: Zum Einstecken in Busgeräte - 2 Steckbuchsen 1mm Durchm. Zum Anschluß an die Busklemme - 2 eindrähtige Adern 0, 8 mm Durchm. Überspannungsableitung - 1 eindrähtige Ader 0, 75 qmm. Abmessungen: 10, 5x11, 6x11, 1 mm. Dehn.Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - BT 24

EAN: 4011281822850 - manufacturer-number: 677029 - Time switch for bus system 4-ch Bus system EIB/KNX, Other bus systems None, Daily program, Weekly program, Annual program, Mounting method DRA, Width in number of modular spacings 6, External programming, Number of channels 4, Summer-/winter switchover, Radio-controlled (DCF77), Sub-clocks controllable over bus-system, Autonomy 13140h, Degree of protection (IP) IP20, Bus connection included, Blueway-Classification Component for energy saving solution, Year time switch REG-K/4/324 DCF-77, light grey 4-channel year time switch with power supply unit and integrated DCF receiver. To be completed with the DCF-77 antenna for radio-controlled time synchronisation. Time and date can be issued on the bus. The device can be programmed manually on the device itself or on the PC using the CTS Chip Tool software. With bus coupler. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal, a data rail is not necessary. After programming on the PC, all switching times are exported to a memory chip available as an accessory, and transmitted from this into one or more time switches. Time functions: - 324 non-volatile switching times for selectable daily, weekly  , ,and date commands, impulse commands - 1x switching operation for holiday/public holidays - 10 weekly programs for holidays and public holidays  , ,per channel - Free formation of channel and weekday blocks - Manual switching is possible via preselection and  , ,permanent switches - Random program can be activated - High reserve power - Automatic changeover between summer and  , ,winter time - Automatic time synchronisation with DCF possible INSTABUS EIB software functions: Switching. Dimming. Send time and date. Scene. Priority.  , ,Operating voltage: Bus, DC 24 V AC 230 V ¡¾10%,  , ,50-60 Hz for antenna  , ,Accuracy: ¡Â¡¾1s/day  , ,Reserve power: 1.5 years at full operability. Data backup  , ,in disconnected state approx. 40 years (EEPROM)  , ,Type of protection: IP 20  , ,Device width: 6 modules = approx. 105 mm  , ,In INSTABUS EIB, to be completed with:  , ,DCF-77 antenna, art. no. 668091.  , ,Accessories: CTS ChipTool software, art. no. 615034.  , ,Memory chip for year time switches, art. no. 668092. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 677029

EAN: 4011281822904 - manufacturer-number: 668091 - Radio receiver In housing, Current supply Other, Mounting method Surface mounted (plaster), Halogen free, Type of fastening Mounting with screw, Colour Grey, RAL-number (akin) 7035, Suitable for degree of protection (IP) IP54, DCF-77 antenna, light grey Antenna for receiving the time by radio signal. The antenna should be connected to a year time switch REG-K/4/324 DCF-77. Type of protection: IP 65 In INSTABUS EIB, to be completed with: Year time switch REG-K/ 4/324 DCF-77, art. no. 677029. Contents: With mounting bracket. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 668091

EAN: 4011281361359 - manufacturer-number: 689701 - Bus connection terminal for bus system Bus system EIB/KNX, Other bus systems None, Model Bus connection terminal, Bus connection terminal, red/dark grey Bus connecting terminal, for connecting max. 4 core pairs to an INSTABUS EIB REG-K, flush-mounted, surfacemounted or built-in device, can also be used as a branch terminal. Consists of two interlocked terminal parts in red (+) and dark grey (-), each with 4 plug-in terminals. For solid conductors with a diameter of 0.6 to 0.8 mm. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 689701

EAN: 4010337570004 - manufacturer-number: 057000 - Bus coupler for bus system 1-ch Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Width in number of modular spacings 0, Number of connections sensor/actuator 1, Type of fastening Mounting with claw and screw, Bus coupling unit flush-mounted EIb The bus coupling unit is executed as a flush-mounted device and makes the connection between the instabus EIB and the user module. The user module may be a sensor (Push button, Movement controller, Room thermostat) clipped onto the bus coupling unit. The EIB telegrams received from the line are evaluated and passed on as signals via the user interface (AST) to the user module. In the opposite direction, signals from the user module are converted into EIB telegrams and sent onto the instabus. By means of the programming button the physical adress is transfered into the bus coupling unit. For the unique assignment in the bus topology it is neccessary to program every bus coupling unit with its own unmistakable adress (Physical adress).Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 057000

EAN: 4011377992610 - manufacturer-number: 2130USB - USB Interface for bus system Bus system EIB/KNX, Model USB, Mounting method Flush mounted (plaster), Surface treatment Other, Max. data transmission rate 9600Bd, Bus connection included, With label area, Degree of protection (IP) IP20, USB data interface, UP The USB data interface enables the coupling of a PC for the addressing, programming and diagnosis of instabus EIB components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the instabus EIB if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards. Note: The USB data interface is supported by ETS3 software from version 1.0 upwards and by the PC operating systems Windows 98, 98 SE, ME, 200 and XP. Connection: The connection to the instabus EIB is carried out with the aid of the instabus connecting terminal. The USB connection is carried out with a certified USB cable (1 x B plug required) with a max. length of 5 m. Technical data Power supply: via USB port of the PC Connection: Instabus EIB: instabus connecting terminal USB port: USB socket, type B Transmission protocol: compatible with USB 1.1/2.0 Length of USB cable: max. 5 m Ambient temperature: -5°C to +45°C Storage temperature: -25°C to +70°C Type of protection: IP 20 Protection class: II Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 2130 USB

EAN: 4011377992627 - manufacturer-number: 2130USBREG - USB Interface for bus system Bus system EIB/KNX, Model USB, Mounting method DRA, Width in number of modular spacings 2, Material Plastic, Surface treatment Other, Colour White, Max. data transmission rate 9600Bd, Bus connection included, With label area, Degree of protection (IP) IP20, USB data interface, REG The USB data interface enables the coupling of a PC for the addressing, programming and diagnosis of instabus EIB components. The power is fully supplied by the connected PC via the USB interface. This means that the USB data interface is no longer connected for the instabus EIB if the USB cable is not plugged in. The device is only programmed locally with a physical address via the connected PC and therefore does not have a programming button or programming LED. The firmware of the USB data interface can be updated via a PC and is therefore safeguarded for future standards. Note:The USB data interface is supported by ETS3 software from version 1.0 upwards and by the PC operating systems Windows 98, 98 SE, ME, 200 and XP. Connection: The connection to the instabus EIB is carried out with the aid of the instabus connecting terminal. The USB connection is carried ut with a certified USB cable (1 x B plug required) with a max. length of 5 m. Technical data Power supply: via USB port of the PC Connection: Instabus EIB: instabus connecting terminal USB port: USB socket, type B Transmission protocol: compatible with USB 1.1/2.0 Length of USB cable: max. 5 m Ambient temperature: -5°C to +45°C Storage temperature: -25°C to +70°C Type of protection: IP 20 Protection class: II Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 2130 USB REG

EAN: 4011377992696 - manufacturer-number: 2131.16UP - Switch actuator for bus system 1-ch Bus system EIB/KNX, Mounting method Flush mounted (plaster), Max. switching current 16A, Max. switching power 2200W, Max. number of switching contacts 1, Rated operating voltage 21 ... 32V, Bus connection included, Flush mounted switch actuator 2131.16 UP 1 make contact, with satellite input ETS product family: Output, Product type: Binary output, single Output Number: 1, Switch type: Make contact, floating relay contact (µ-contact), Max. switching voltage: 230 V ~, Max. switching current: 16 A at 230 V ~, Switching capacity: 2500 W incandescent lamps, 2500 W HV halogen lamps, 1000 W fluorescent lamps 120 µF with parallel compensation, cos . = 1, 1200 W fluorescent lamps with twin-lamp circuit, cos . = 1 Connections Load cable: L and L’, brown, 2.5 mm2, length approx. 22 cm, Bus and control cable: instabus EIB + : red, instabus EIB - : black, Binary input 1: green, GND: white, Binary input 2: yellow, GND: brown, Length approx. 35 cm, Satellite input: Assignment can be set via software: a) Push button (make contact) or switch or b) Functionality same as floating binary input Dimensions: Ø 52 mm, height 28 mm (with opening for ceiling rose) Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 2131.16 UP

EAN: 4001869053707 - manufacturer-number: 5WG1301-1AB01 - Logic component for bus system Bus system EIB/KNX, Mounting method DRA, Width in number of modular spacings 1, Bus connection included, Logic object, Logic module N 301 Design: DIN rail mounted. Dimensions: N-system, 1 module wide (1 module = 18 mm). The logic module N 301 is used for the logical operation or evaluation of instabus EIB bus signals. Depending on the application program, the logic module enables: AND + OR logic functions, inversion of bus signals, distribution and/or duplication of bus signals, automatic room divider function for lighting and shutter control in rooms with a flexible partition, priority control of up to four channels. When configuring the logic module, the installer must carry out all the necessary settings. Nominal voltage: DC 29V. Bus connection: via contacts on EIB data rail. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1301-1AB01

EAN: 4001869060583 - manufacturer-number: 5WG1302-1AB01 - Logic component for bus system Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 1, Time module N 302 Design: DIN rail mounted device. Dimensions: N-system, 1 module wide (1 module = 18 mm). The time module N 302 is used for the ON and OFF delay and inversion of instabus EIB bus signals. The time module enables: the inversion of signals, ON and OFF delay of signals, time switch function (e.g. staircase lighting). During the configuration of the time module, the installer must carry out all the necessary settings. Nominal voltage: DC 29V. Bus connection: via contacts on EIB data rail. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1302-1AB01

EAN: 4001869072968 - manufacturer-number: 5WG1341-1AB01 - Logic component for bus system Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 1, Bus connection included, Event module N 341 Design: DIN rail mounted. Dimensions: N-system, 1 module wide (1 module = 18 mm). The event module N 341 is used to process time or event tasks for the instabus EIB. The event module enables: the processing of up to 400 time tasks in up to 125 day programs, the assignment of day programs to up to 150 calendar entries (date or date range), the definition of up to three periods for periodic sequences with a duration of 2 to 40 days, the processing of up to 200 event tasks in up to 200 event programs, sending of text, temperature values, dimming values and switching values, event triggering by value exceeding or falling below the limit value, selection of retriggering of an event program, learning of event tasks. During the configuration of the event module, the installer must carry out all the necessary settings. Nominal voltage: DC 29V. Bus connection: via contacts on EIB data rail Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1341-1AB01

EAN: 4001869054049 - manufacturer-number: 5WG1562-1AB01 - Switch actuator for bus system 2-ch Bus system EIB/KNX, Mounting method DRA, Width in number of modular spacings 2, Max. switching current 6A, Max. number of switching contacts 2, Binary output N 562 2x230V AC/10A Device with N-system dimensions of the instabus EIB, with 2 floating contacts (bistable relays) for 2 independent switching channels, for switching electrical loads on and off directly or with priority control, as a time switch or with ON/OFF delay, or for controlling electrothermal valve drives with monitoring of the temperature sensor, 3 window contacts and an alarm signal per channel, for defined switching on bus voltage failure and recovery, with selectable relay operation (make contact/break contact). Power supply: via the bus line. Rated current: 10 A. Dimensions: DIN rail mounted device with N-system dimensions, width 2 modules (1 module = 18 mm) Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 5WG1562-1AB01

EAN: 4011334224624 - manufacturer-number: 75261189 - Movement sensor for bus system 0...180° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Flush mounted (plaster), Material Plastic, Type of surface Matt, Colour White, Staircase monitoring, Optimum mounting height 1,1m, Max. transmission range sideways 6m, Max. transmission range frontally 10m, Detection angle horizontal from/to 0 ... 180°, Colour variant Polar white, Blueway-Classification Component for energy saving solution, Movement controller 180 flush-mounted (1.10m), S.1, polar white The instabus 180° movement controller is pushed onto a flush-mounted bus coupling unit (BCU). It reacts to heat movements triggered by persons, animals or objects and sends switching telegrams in dependency on the preset parameters to the instabus EIB. The devices range can also be adapted to local requirements by means of a potentiometer. If more than one detector acts on a group of lights, extensions can be set up. The enclosed cover plate can be placed on the detector to restrict the recognition range to 90°. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75261189

EAN: 4042811015848 - manufacturer-number: 680129 - Light system interface/Dali Bus system EIB/KNX, Other bus systems None, Model Light system interface/Dali, Mounting method DRA, Width in number of modular spacings 6, With LED indication, Updateable, Operating voltage 230V, Protocol Other, Degree of protection (IP) IP20, EIB KNX INSTABUS DALI gateway REG-K / 1 / 16 / 64 The DALI gateway connects the INSTABUS EIB with digital electronic ballasts, which are equipped with a DALI interface. The gateway is the DALI master and power supply for the electronic ballasts. It supports the switching and dimming of up to 64 electronic ballasts in 16 groups and the control of 16 lightscenes. Brightness values or error messages in the DALI devices can be sent to the EIB and visualised on display units. The DALI is commissioned and configured with the integrated display and operator buttons. They also permit the user to change group assignments and scene settings at any time without software. With 2 inputs, e.g. for the connection of push-buttons. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal, a data rail is not necessary. The network and the DALI cable as well as the switch inputs are connected via screw terminals on the device. Supply voltage: AC 110-240 V, 50-60 Hz Inputs: 2, passive DC 9-36 V or AC 9-24 V Outputs: DALI D+, D in line with DALI specification DC 16-18 V, 150 mA, short-circuit-proof Connecting cable: 1.5 - 2.5 mm2 Type of protection: IP 20 Device width: 6 modules = approx. 108 mm Contents: With bus connecting terminal. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 680129

EAN: 4042811015879 - manufacturer-number: 681829 - USB Interface for bus system Bus system EIB/KNX, Model USB, Mounting method DRA, Width in number of modular spacings 2, Material Plastic, Material quality Other, Colour Grey, RAL-number (akin) 7035, Max. data transmission rate 9600Bd, Bus connection included, Degree of protection (IP) IP20, EIB KNX USB interface REG-K For connecting a programming or diagnostics device with a USB1.1 or USB2 interface to the INSTABUS EIB. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal, a data rail is not necessary. With integrated bus coupler. Device width: 2 modules = approx. 36 mm Contents: With bus connecting terminal and cable cover. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 681829

EAN: 4042811015855 - manufacturer-number: 681799 - USB Interface for bus system Bus system EIB/KNX, Model USB, Mounting method Flush mounted (plaster), Material Plastic, Material quality Other, Max. data transmission rate 9600Bd, Bus connection included, Degree of protection (IP) IP20, EIB KNX USB interface, flush-mounted For connecting a programming or diagnostics device with a USB1.1 or USB2 interface to the INSTABUS EIB. For screw mounting in the size 60 installation box. With integrated bus coupler. The device is connected to the bus with a bus connecting terminal. Compatible with ETS 3. Mounting depth: 20 mm To be completed with: Central plate for telephone socket-outlet TAE, art. no. 2928.., 2979.., 2978.. or 2938... Contents: With bus connecting terminal. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 681799

EAN: 4011334251613 - manufacturer-number: 75261589 - Movement sensor for bus system 0...180° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Flush mounted (plaster), Material Plastic, Type of surface Matt, Colour White, Slide switch, Staircase monitoring, Optimum mounting height 1,1m, Max. transmission range sideways 6m, Max. transmission range frontally 10m, Detection angle horizontal from/to 0 ... 180°, Min. switch-on time 10s, Colour variant Polar white, Blueway-Classification Component for energy saving solution, Movement controller 180 comfort flush-mounted (1.10m), S.1/B.3/B.7 Glas, polar white The instabus movement controller comfort is pushed onto a flush-mounted bus coupling unit (BCU). It reacts to heat movements triggered by persons, animals or objects and sends telegrams to the instabus EIB in dependence on the set mode. The operating modes are switching, value transmitter and light scene request, and also the less sensitive message (signalling) mode. Here the monitor does not react until the movement signal has been queried several times. A slide switch enables manual mode of the movement controller comfort. The device can be adapted to the local situation by means of three potentiometers, a potentiometer for delay time setting, brightness limiting value and sensivity. The enclosed cover plate can be placed on the detector to restrict the recognition range to 90°. Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75261589

EAN: 4011334251729 - manufacturer-number: 75261689 - Movement sensor for bus system 0...180° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Flush mounted (plaster), Material Plastic, Type of surface Matt, Colour White, Slide switch, Staircase monitoring, Optimum mounting height 2,2m, Max. transmission range sideways 6m, Max. transmission range frontally 12m, Detection angle horizontal from/to 0 ... 180°, Min. switch-on time 10s, Colour variant Polar white, Blueway-Classification Component for energy saving solution, Movement controller 180 comfort flush-mounted (2.20m), S.1/B.1/B.3/B.7 Glas polar white The instabus movement controller comfort is pushed onto a flush-mounted bus coupling unit (BCU). It reacts to heat movements triggered by persons, animals or objects and sends telegrams to the instabus EIB in dependence on the set mode. The operating modes are switching, value transmitter and light scene request, and also the less sensitive message (signalling) mode. Here the monitor does not react until the movement signal has been queried several times. A slide switch enables manual mode of the movement controller comfort. The device can be adapted to the local situation by means of three potentiometers, a potentiometer for delay time setting, brightness limiting value and sensivity. The enclosed cover plate can be placed on the detector to restrict the recognition range to 90°.Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75261689

EAN: 4011334251361 - manufacturer-number: 75316003 - Heating actuator for bus system Bus system EIB/KNX, Mounting method DRA, Width in number of modular spacings 4, Correcting variable consistent, Correcting variable switching, Number of outputs 6, Max. output current 0,5A, Blueway-Classification Component for energy saving solution, Heating actuator 6gang Triac 230 V AC RMD, 75316003 The heating actuator is for activation of electro-thermal actuator drives (ETA) for heating systems or cooling systems. It has 6 electronic outputs, which silently activate the actuator drives in response to EIB telegrams. Up to 4 electro-thermal actuator drives (e. g. Heimeier 1835, Sauter MTX 116F200, Möhlenhoff AA 2001-00-1) can be connected to each output. Outputs are actuated either as switching or as a PWM signal, depending on the setting of the manipulated variable (1 bit or 8 bit). The actuator is able to detect overloads / short circuits at one output / at multiple outputs. In this case the short-circuited outputs after a short identification time can be permanently deactivated, parameters can also be set for overloads to be reported on the bus. Mains power failures can be reported on the bus. Summer or winter mode changeover can be performed by object. In addition an anti-seize routine is available for all drives, and cyclic monitoring can be performed for all manipulated variables. If during cyclic monitoring manipulated variable telegrams are found to be missing, emergency mode will be activated for the respective output, using a parameterised manipulated variable defined for summer or winter mode. Emergency mode can also be activated on bus power failure / restoration. Each output can be positively activated separately by an object. For this a parameterisable manipulated variable, different for summer and winter mode, is assigned to the respective output. Forced position can also be activated on bus power failure / restoration. In the unprogrammed condition the actuator is set for pulse width modulation with a manipulated variable of 50 % and a cycle time of 15 minutes. This permits the actuator to be tested for functioning even without bus power. Technical Data: instabus EIB supply voltage : 21 - 32 V DC, instabus EIB power consumption : max. 125 mW, Mains supply : AC 230/240 V, 50/60 Hz, Overall power dissipation : approx. 2 W, instabus EIB connection : instabus connecting terminals, Connection of mains and outputs : screw terminals 0.2 – 4 mm² single wire or 2 x 0.2 – 2.5 mm² single wire, 0.75 – 4 mm² stranded wire without ferrule or 0.5 – 2.5 mm² stranded wire with ferrule, Outputs : 6, Type of contact : electronic, Switching capacity : IN = 50 mA resistive at 230 / 240 V AC, Minimum load per output used : 1 servo-drive, Make current : max. 1.5 A per output, Number of electro-thermal servo-drives to be connected to an output : max. 4 per output (depending on type), Ambient temperature : -5 °C ... +45 °C, Max. housing temperature : TC = 75 °C, Storage temperature : -25 °C ... +70 °C, Installation width : 72 mm (4 pitch) Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75316003

EAN: 4010337070009 - manufacturer-number: 107000 - USB Interface for bus system Bus system EIB/KNX, Other bus systems None, Model USB, Mounting method Flush mounted (plaster), Width in number of modular spacings 0, Material Other, Material quality Other, Surface treatment Other, Type of surface Not applicable, Colour Other, Bus connection included, Degree of protection (IP) IP20, photographed by EIB3D.COM USB data interface UP The USB data interface permits the connection of a PC to the instabus KNX / EIB. The interface enables Instabus devices to be addressed, programmed and diagnosed by means of the ETS 3 or the ETS 3 Starter. The device electronics get their power supply completely from the USB interface of the connected PC. For this reason, the USB data interface cannot be accessed from the bus side unless the USB cable is plugged in and the the PC is on. The physical address of the interface can be programmed only locally (ETS) by means of the connected PC. For this reason, the data interface has neither a programming button nor a programming LED. The firmware of the USB data interface can be updated with the local PC so that the device can easily be adapted to future standards. For proper functioning, the device requires only the standard Windows HID drivers which are installed and activated automatically when the data interface is plugged into the PC. The device can be accessed by the ETS3 only after successful installation. Technical data instabus EIB supply voltage: 21 - 32 V DC power consumption: 150 mW max. connection: instabus connecting and branching terminal USB Rate of transmission: typically 9.6 kbaud Transmission protocol: compatible with USB standards 1.1 and 2.0 PC port: USB connecting socket type B Connecting cable: max. 5 m use USB-certified connecting cableNote:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 107000

EAN: 4010337118008 - manufacturer-number: 111800 - Binary input for bus system 2-ch Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of inputs 2, Degree of protection (IP) IP20, photographed by EIB3D.COM 2-channel push button interface The 2-channel push button interface has 2 independent channels which – depending on parameterization – can be used as inputs or alternatively as outputs. The push button interface can therefore be used to poll its inputs for the switching state of up to 2 potential-free push buttons/switches with a common reference potential and send the corresponding telegrams to the instabus. These may be telegrams for switching or dimming, shutter/blind control or value transmitter applications (dimming value transmitter, light-scene extension, temperature or brightness value transmitter). Moreover, 2 switching event counters or 1 pulse counter (only channel 1) are available. Channels 1 and 2 can be used alternatively as independent outputs for controlling up to two LEDs. To increase the output current (cf. Technical Data), the channels can also be connected in parallel if they are parameterized alike. The outputs are short-circuit-proof and protected against overloading and false polarity. Connecting 230 V signals or other external voltages to the inputs is not permitted. Technical data Instabus EIB supply Voltage: 21 - 32 V DC SELV Power consumption: typ. 150 mW Connection: bus connecting and branching terminal Inputs: Number: up to 2 (depending on parameterization: channel 1 to 2) Line length: 25 cm prefabricated, extendable to 5 m max. Scanning voltage: continuous signal Loop resistance: max. 2 kOhm for safe detection of a 1 signal (rising edge) Outputs: Number: up to 2 (depending on parameterization: channel 1 and/or 2) Line length: 25 cm prefabricated, extendable to 5 m max Output current: max. 0.8 mA per output channel (at 1.5 V, typ. for red low-current LED) For parallel connection, the maximum total output current increases to 1.6 mA. In the event of parallel connection, outputs 1 and 2 must be parameterized exactly alike (none of the output signals flashing) The outputs are short-circuit-proof, protected against overloading and false polarity. Output voltage: typ. 1.5 V (e.g. red low-current LED) (5 V with outputs open circuit)Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 111800

EAN: 4010337119005 - manufacturer-number: 111900 - Binary input for bus system 4-ch Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of inputs 4, Degree of protection (IP) IP20, 4-channel push button interface The 4-channel push button interface has 4 independent channels which – depending on parameterization – can be used as inputs or alternatively as outputs (only channels 1 or 2). The push button interface can therefore be used to poll its inputs for the switching state of up to 4 potential-free push buttons/switches with a common reference potential and send the corresponding telegrams to the instabus. These may be telegrams for switching or dimming, shutter/blind control or value transmitter applications (dimming value transmitter, light-scene extension, temperature or brightness value transmitter). Moreover, 2 switching event counters or 2 pulse counters are available. Channels 1 and 2 can be used alternatively as independent outputs for controlling up to two LEDs. To increase the output current (cf. Technical Data), the channels can also be connected in parallel if they are parameterized alike. The outputs are short-circuit-proof and protected against overloading and false polarity. Connecting 230 V signals or other external voltages to the inputs is not permitted. Technical data Instabus EIB supply Voltage: 21 - 32 V DC SELV Power consumption: typ. 150 mW Connection: bus connecting and branching terminal External supply --- Inputs: Number: up to 4 (depending on parameterization: channel 1 to 4) Line length: 25 cm prefabricated, extendable to 5 m max. Scanning voltage: continuous signal Loop resistance: max. 2 kOhm for safe detection of a 1 signal (rising edge) Outputs: Number: up to 2 (depending on parameterization: channel 1 and/or 2) Line length: 25 cm prefabricated, extendable to 5 m max Output current: max. 0.8 mA per output channel (at 1.5 V, typ. for red low-current LED) For parallel connection, the maximum total output current increases to 1.6 mA. In the event of parallel connection, outputs 1 and 2 must be parameterized exactly alike (none of the output signals flashing) The outputs are short-circuit-proof, protected against overloading and false polarity. Output voltage: typ. 1.5 V (e.g. red low-current LED) (5 V with outputs open circuit)Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 111900

EAN: 4010337247654 - manufacturer-number: 1247651 - Touch sensor for bus system 4-fold Bus system EIB/KNX, Other bus systems None, Mounting method Other, With anti-theft/dismantling protection, Number of actuation points 4, With LED indication, With label area, Material Other, Material quality Other, Surface treatment Other, Type of surface Not applicable, Colour Aluminium, Degree of protection (IP) IP20, Colour variant Aluminium, ITS push sensor, 4-fold with controller, alu The ITS push sensor is plugged onto a flush-mounted bus coupler (cf. wiring diagram). On pressing of a key, the ITS push sensor transmits telegrams depending on the parameters programmed via the instabus EIB. These may include telegrams for switching or dimming (also single-key dimming) or for blind/shutter control. It is also possible to program value-transmit functions such as dimming value transmitter,light-scene extensions, 2-byte analog value transmitter (temperature or brightness transmitter) or 1-byte universal value transmitter (continuous run between start and target value). The keys or rockers can be independently assigned to the different functions. The ITS push sensor with controller moreover permits disabling of individual keys or rockers or the complete push sensor. The operation-LED can be switched on or off via an object (in this case, a disabling function is no longer available). On removal of the ITS push sensor from the bus coupler, the device can transmit an alarm message (1 bit or 1 byte). Technical data instabus EIB supply voltage: 21 - 32 V DC SELV power consumption: typically 150 mW connection: 2 x 5-pole male connector strip External supply --- Input: --- Output: --- Response to mains failures bus voltage only: object values are deleted, LEDs switch off mains voltage only: --- bus and mains voltage: --- Response on return of voltage bus voltage only: no reaction (cf: Disable object in software information mains voltage only: --- bus and mains voltage: --- Type of protection: IP 20 Safety class: III Mark of approval: EIB Ambient temperature: -5 °C ... +45 °C GIRA-No. 1247651 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 1247651

EAN: 4010337080008 - manufacturer-number: 108000 - USB Interface for bus system Bus system EIB/KNX, Other bus systems None, Model USB, Mounting method DRA, Width in number of modular spacings 2, Material Other, Material quality Other, Surface treatment Other, Type of surface Not applicable, Colour Other, Degree of protection (IP) IP20, USB data interface REG The USB data interface permits the connection of a PC to the instabus KNX / EIB. The interface enables Instabus devices to be addressed, programmed and diagnosed by means of the ETS 3 or the ETS 3 Starter. The device electronics get their power supply completely from the USB interface of the connected PC. For this reason, the USB data interface cannot be accessed from the bus side unless the USB cable is plugged in and the the PC is on. The physical address of the interface can be programmed only locally (ETS) by means of the connected PC. For this reason, the data interface has neither a programming button nor a programming LED. The firmware of the USB data interface can be updated with the local PC so that the device can easily be adapted to future standards. For proper functioning, the device requires only the standard Windows HID drivers which are installed and activated automatically when the data interface is plugged into the PC. The device can be accessed by the ETS3 only after successful installation. Technical data instabus EIB supply voltage: 21 - 32 V DC power consumption: 150 mW max. connection: instabus connecting and branching terminal USB Rate of transmission: typically 9.6 kbaud Transmission protocol: compatible with USB standards 1.1 and 2.0 PC port: USB connecting socket type B Connecting cable: max. 5 m use USB-certified connecting cableNote:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 108000

EAN: 4011377995772 - manufacturer-number: 2132.6UP - Switch actuator for bus system 2-ch Bus system EIB/KNX, Mounting method Flush mounted (plaster), Max. switching current 6A, Max. switching power 1200W, Max. number of switching contacts 2, Rated operating voltage 32 ... 21V, Bus connection included, 2-channel switching actuator, UP, 6 A Switching actuators are used for activating electrical consumers via the instabus EIB. The switching commands come, for instance, from touch sensors or from binary inputs of the instabus EIB system. Two extension inputs can be used for local control by means of conventional pushbuttons/switches or as binary inputs for potential-free contacts (only with bus voltage applied). The device is supplied from the instabus EIB and does not need a supplementary power supply. Technical data 230 V switching capacity : 2 x 6 A / 230 V AC Rated power incandescent lamps : 1200 W HV halogen lamps : 1200 W capacitive load : AC 230 V, 6 A, max. 14 µF convent. transformers : 500 VA Tronic transformers : 500 W Inrush current : 120 A / 20 ms Load line: : 1.5 mm² stranded with ferrule, length approx. 20 cm Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 2132.6 UP

EAN: 4042811026585 - manufacturer-number: 645129 - Heating actuator for bus system Bus system EIB/KNX, Other bus systems None, Mounting method DRA, Width in number of modular spacings 4, Bus connection included, Correcting variable consistent, Correcting variable switching, Valve protection function, Number of binary inputs 0, Max. switching current (resistive load) 0,05A, Number of outputs 6, Max. output current 0,05A, Switching voltage from/to 230 ... 240V, Degree of protection (IP) IP20, Blueway-Classification Component for energy saving solution, EIB KNX Heating actuator REG-K / 6x230 / 0.05 A For actuation of thermoelectric valve drives for heating or cooling ceilings. The heating actuator has 6 electronic outputs. Up to 4 valve drives can be connected to each output. The outputs are either switch activated (1 bit) or PWM signal (1 byte) activated. Each output is overload-protected and short-circuit-protected. For installation on DIN rails EN 50022. The bus is connected using a bus connecting terminal, a data rail is not necessary. INSTABUS EIB software functions: Cycle time, status feedback, summer and winter operation, cyclical monitoring of variables, locking each output in a forced position, behaviour on bus power failure and recovery, overload and short circuit status, mains power loss reporting, collective fault reporting connected to all valves, transmission of the largest 1 byte variable value. Nominal voltage: AC 230 V, 50-60 Hz Outputs: 6, electronic Nominal current: 0.05 A, ohmic Starting current: max. 1.5 A Minimum load per used output: 1 valve drive Number of valve drives:max. 4 per output Device width: 4 modules = approx. 72 mm Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 645129

EAN: 4042811034566 - manufacturer-number: 619219 - Touch rocker for bus system white Bus system EIB/KNX, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour White, RAL-number (akin) 9010, Rockers for 2-gang push-button module Thermoplastic brilliant, polar white glossy For System M. The rockers are attached to the 2-gang push-button module. To be completed with: Push-button module, 2-gang, art. no. System M 568499. In INSTABUS EIB, to be completed with: EIB push-button module, 2-gang, art. no. System M 625299. In INSTABUS EIB EASY, to be completed with: Easy push-button module, 2-gang, art. no. System M 762192. Accessories: Protective hood for plaster, System M, art. no. 627591... Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 619219

EAN: 4011334283287 - manufacturer-number: 75161780 - Touch sensor for bus system 2-fold Bus system EIB/KNX, Bus system radio frequent, Other bus systems None, Mounting method Flush mounted (plaster), With anti-theft/dismantling protection, Number of actuation points 2, With LED indication, With label area, Material Plastic, Colour Other, EIB KNX Push-button 1gang comfort with labelling field S.1/B.1/B.3/B.7 Glas for white and polar white, 75161780 The push button comfort is plugged onto a flush-mounted bus coupler (flush- mounted BCU). The keys of the device can be programmed for the following functions: switching, dimming, blind/shutter control, value transmitter, light-scene recall, forced guidance and control. Key assignment is free and fixed in the project. Depending on the preset functions, a press on any of the keys sends telegrams to the KNX / EIB which trigger switching, dimming or blind/shutter functions, recall or store light-scenes and set dimming, brightness or temperature values in the respective actuators. The central LED indicates when the touch sensor is ready for operation. Each key is equipped with an LED which can be used for indicating the functional status. Each touch sensor Komfort permits the activation of a second user level with reduced functions (e.g. cleaning service lighting). Depending on the software (SW), the user level can be switched over by local control (only 4-channel type), time control or by bus telegrams. The 4-channel touch sensors Komfort can be locked by entering a four-digit code. Technical Data: Type of protection: IP 20, Safety class: III, Mark of approval: KNX / EIB, Ambient temperature: -5 °C ... +45 °C, Storage / transport temperature: -25 °C ... +70 °C ( storage above +45 °C reduces the service life), Mounting position: any, Minimum distances: none, Type of fastening: plug-in on flush-mounted bus coupling unit, instabus EIB supply: voltage: 21 - 32 V DC SELV, power consumption: typically 150 mW, connection: 2 x 5 pole male connector strip, Response to mains failures bus voltage only: no reaction, Response on return of voltage bus voltage only: all object values deleted (cf. software information) Manufacturer: Berker Color: for white and polar white Manufacturer-No.: 7516 17 80 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75161780

EAN: 4011334283348 - manufacturer-number: 75163780 - Touch sensor for bus system 6-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), With anti-theft/dismantling protection, Number of actuation points 6, With LED indication, With label area, Material Plastic, Surface treatment Other, Colour Other, EIB KNX Push-button 3gang comfort with labelling field S.1/B.1/B.3/B.7 Glas for white and polar white, 75163780 The push button comfort is plugged onto a flush-mounted bus coupler (flush- mounted BCU). The keys of the device can be programmed for the following functions: switching, dimming, blind/shutter control, value transmitter, light-scene recall, forced guidance and control. Key assignment is free and fixed in the project. Depending on the preset functions, a press on any of the keys sends telegrams to the KNX / EIB which trigger switching, dimming or blind/shutter functions, recall or store light-scenes and set dimming, brightness or temperature values in the respective actuators. The central LED indicates when the touch sensor is ready for operation. Each key is equipped with an LED which can be used for indicating the functional status. Each touch sensor Komfort permits the activation of a second user level with reduced functions (e.g. cleaning service lighting). Depending on the software (SW), the user level can be switched over by local control (only 4-channel type), time control or by bus telegrams. The 4-channel touch sensors Komfort can be locked by entering a four-digit code. Technical Data: Type of protection: IP 20, Safety class: III, Mark of approval: KNX / EIB, Ambient temperature: -5 °C ... +45 °C, Storage / transport temperature: -25 °C ... +70 °C ( storage above +45 °C reduces the service life), Mounting position: any, Minimum distances: none, Type of fastening: plug-in on flush-mounted bus coupling unit, instabus EIB supply: voltage: 21 - 32 V DC SELV, power consumption: typically 150 mW, connection: 2 x 5 pole male connector strip, Response to mains failures bus voltage only: no reaction, Response on return of voltage bus voltage only: all object values deleted (cf. software information), Labelling field length (W x H) 52,3 x 15,6 mm, with white operation LED and 6 red status LEDs Manufacturer: Berker Color: for white and polar white Manufacturer-No.: 7516 37 80 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75163780

EAN: 4011334280859 - manufacturer-number: 75261559 - Movement sensor for bus system 0...180° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Flush mounted (plaster), Material Plastic, Type of surface Brilliant, Colour White, Slide switch, Staircase monitoring, Optimum mounting height 1,1m, Max. transmission range sideways 6m, Max. transmission range frontally 10m, Detection angle horizontal from/to 0 ... 180°, Min. switch-on time 10s, Colour variant Polar white, Blueway-Classification Component for energy saving solution, Movement controller sensor 180 comfort with slide switch for off/automatic/on white glossy, 1.10 m, S.1/ B.3 / B.7, 75261552 The instabus movement controller comfort is designed for internal use and is pushed onto a flushmounted bus coupling unit (BCU). It reacts to heat movements triggered by persons, animals or objects and sends telegrams to the instabus EIB in dependence on the set mode. The operating modes are switching, value transmitter and light scene request, and also the less sensitive signalling mode. Here the monitor does not react until the movement signal has been queried several times. A slide switch enables manual mode of the movement controller comfort. The device can be adapted to the local situation by means of three potentiometers. Technical Data Protection class: IP 20, Insulation voltage: in accordance with VDE 0829 Part 230, Test mark: EIB, Ambient temperature: - 5 °C to + 45 °C, Storage temperature: - 25 °C to + 70 °C (storage at temp. over 45°C reducers the service life), Installation position: The detection ranges indicated are reached with vertical installation of the FM bus coupling unit and the AST underneath, Fastening method: Push onto BCU, Supply instabus EIB Voltage: 24 V DC (+6 V / -4 V) via BCU, Power consumption: typ. 110 mW, Terminal: 2 x 5-pole plug connector, Behaviour on voltage return: Bus voltage only: Lighting mode: Software-dependent (80 s immunity time), Signalling mode: No reaction (80 s immunity time), Bus and mains voltage: Lighting mode: Software-dependent (80 s immunity time), Signalling mode: No reaction (80 s immunity time), Input: Adapter lens type: for 1.10 m installation height Detection angle: 180°, Nominal range, front: 10 m, Nominal range, side: 2 x 6 m, Installation height for nominal range 1.10 m, No. of lenses/lens levels: 18 / 2 Manufacturer: Berker Color: white glossy Manufacturer-No.: 7526 15 52 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75261559

EAN: 4011334280835 - manufacturer-number: 75261659 - Movement sensor for bus system 0...180° Bus system EIB/KNX, Other bus systems None, Model Movement sensor, Mounting method Flush mounted (plaster), Material Plastic, Type of surface Brilliant, Colour White, Slide switch, Staircase monitoring, Optimum mounting height 2,2m, Max. transmission range sideways 6m, Max. transmission range frontally 12m, Detection angle horizontal from/to 0 ... 180°, Min. switch-on time 10s, Colour variant Polar white, Blueway-Classification Component for energy saving solution, Movement controller sensor 180 comfort with slide switch for off/automatic/on white glossy, 1.10 m, S.1/ B.3 / B.7, 75261552 The instabus movement controller comfort is designed for internal use and is pushed onto a flushmounted bus coupling unit (BCU). It reacts to heat movements triggered by persons, animals or objects and sends telegrams to the instabus EIB in dependence on the set mode. The operating modes are switching, value transmitter and light scene request, and also the less sensitive signalling mode. Here the monitor does not react until the movement signal has been queried several times. A slide switch enables manual mode of the movement controller comfort. The device can be adapted to the local situation by means of three potentiometers. Technical Data Protection class: IP 20, Insulation voltage: in accordance with VDE 0829 Part 230, Test mark: EIB, Ambient temperature: - 5 °C to + 45 °C, Storage temperature: - 25 °C to + 70 °C (storage at temp. over 45°C reducers the service life), Installation position: The detection ranges indicated are reached with vertical installation of the FM bus coupling unit and the AST underneath, Fastening method: Push onto BCU, Supply instabus EIB Voltage: 24 V DC (+6 V / -4 V) via BCU, Power consumption: typ. 110 mW, Terminal: 2 x 5-pole plug connector, Behaviour on voltage return: Bus voltage only: Lighting mode: Software-dependent (80 s immunity time), Signalling mode: No reaction (80 s immunity time), Bus and mains voltage: Lighting mode: Software-dependent (80 s immunity time), Signalling mode: No reaction (80 s immunity time), Input: Adapter lens type: for 1.10 m installation height Detection angle: 180°, Nominal range, front: 10 m, Nominal range, side: 2 x 6 m, Installation height for nominal range 1.10 m, No. of lenses/lens levels: 18 / 2 Manufacturer: Berker Color: white glossy Manufacturer-No.: 7526 15 52 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75261659

EAN: 4011334283430 - manufacturer-number: 75662780 - Touch sensor for bus system 4-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), With anti-theft/dismantling protection, Number of actuation points 4, With LED indication, With label area, With display, Material Plastic, Colour Other, With room temperature controller, Push-button 2gang with room thermostat, display and labelling field B.1/B.3/B.7 Glas for white and polar white, 75662780 The RT touch sensor combines the functions of touch sensor, room temperature controller and room temperature timer clock in the same housing, thus permitting the control of many different functions in a building. The touch sensor functions are dependent on programming and on the other devices in your EIB installation. The RT touch sensor is adapted to your individual needs and to the functions of the building. Functioning and operation of the touch sensor should be agreed between the user and the electrical .tter. Display functions Room temperature and/or outside temperature and reference temperature value, Simple and fast adaption of the room temperature, Day of the week and time of day (only with EIB DCF77 clock), Adaptation of the reference temperature values for different operating modes, Local programming of the room temperature timer clock Function keys Switching and dimming of lighting, Opening/closing and positioning of blinds and shutters, Recalling and storing of 8 light scenes, Transmitting temperature and brightness values, Defining operating modes for the room temperature controller, Activating/deactivating the room temperature timer clock LED functions Status display or display of pressed key, LED on or off Technical Data: Type of protection: IP 20, Safety class: III, Mark of approval: KNX / EIB, Ambient temperature: -5 °C ... +45 °C, Storage/ transport temperature: -25 °C - +70 °C (storage over +45 °C will reduce pr oduct life), Mounting position: Any (preferably vertical/ display up), Minimum distances: None, Type of fastening: Plugging onto flush-mounted BCU, Supply instabus EIB: Voltage 21 - 32 V DC (via flush- mounted BCU), Power consumption: Typically 150 mW (via flush-mounted BCU), Wiring: 2 x 5 pole male connector strip (PEI), Room temperature regulator (internal temperature sensor): Measuring range: 0 °C - + 40 °C ±1 %, Resolution: 0.1 K, Atmospheric humidity: 0 % to 95 % (no moisture condensation), Internal clock: Resolution 1 minute, Deviation Max. of 8 minutes a day, In order to minimize the deviation, the internal clock should be set and thus be updated hourly via the bus. Response to voltage failure: Bus voltage only all object values will be deleted, Push button function: no response, LED’s switch off, Room temperature regulator no response, control off, Response to return of voltage Bus voltage only Push button function: no response, Room temperature regulator: The controller initializes. According to the parameterization, different temperature values and the status will be transmitted and the switch-over objects will be updated, Dimensions: Width: 70 mm, Height: 55 mm, Depth: 13 mm (without PEI) Manufacturer: Berker Color: for white and polar white Manufacturer-No.: 7566 27 80 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75662780

EAN: 4042811029746 - manufacturer-number: 628019 - Touch sensor for bus system 3-fold Bus system EIB/KNX, Mounting method Flush mounted (plaster), Bus connection included, Number of actuation points 3, With LED indication, With label area, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour White, RAL-number (akin) 9010, Degree of protection (IP) IP20, Colour variant Polar white, Push-button, 1-gang plus Thermoplastic brilliant, polar white For System Design. With integrated bus coupling unit. Push-button with two operating buttons, operating display, two blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. Contents: With protective hood for plaster. With bus connecting terminal. Manufacturer: Merten Color: polar white Manufacturer- No.: 628019 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 628019

EAN: 4011334247494 - manufacturer-number: 75010009 - Power supply for bus system 320mA Bus system EIB/KNX, Mounting method DRA, Width in number of modular spacings 4, With LED indication, Number of integrated choke coils 1, Number of lines to feed 2, Max. output current 320mA, KNX/EIB Power supply 320 mA RMD light grey This device is a product of the instabus-EIB system and complies with the EIBA Guidelines. Detailed technical knowledge acquired in instabus training courses is a prerequisite to proper understanding. The 320 mA and 640 mA power supplies generate and monitor the instabus EIB system voltage of 30V DC (SELV). 320 mA power supply: Supply of a bus line with max. 32 instabus users via the BUS output without additional instabus EIB choke. The 30V DC output in both devices is not equipped with a choke and permits supplying another line (e.g. main line) via a separately installed instabus EIB choke. This output can alternatively be used for the supply of further functional devices (e.g. auxiliary voltage for binary inputs). Important: The distribution of loads over the outputs is optional, provided that the total rated current is not exceeded. The instabus EIB power supply unit must be installed exclusively on a 35 mm DIN rail in distribution boxes or in switch cabinets. Ensure sufficient ventilation to prevent the admissible temperature range of the device from being exceeded. Technical Data: Mains voltage AC : 161 to 264 V AC, 50/60 Hz, Operating voltage DC : 176 V DC to 270 V DC, Power dissipation : typically Manufacturer: Berker Manufacturer-No.: 7501 00 09 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 75010009

EAN: 4042811029753 - manufacturer-number: 628119 - Touch sensor for bus system 5-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Bus connection included, Number of actuation points 5, With LED indication, With label area, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour White, RAL-number (akin) 9010, Degree of protection (IP) IP20, Colour variant Polar white, Push-button, 2-gang plus Thermoplastic brilliant, polar white For System Design. With integrated bus coupling unit. Push-button with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. Contents: With protective hood for plaster. With bus connecting terminal. Manufacturer: Merten Color: polar white Manufacturer-No.: 628119 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 628119

EAN: 4042811049003 - manufacturer-number: 628146 - Touch sensor for bus system 5-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Bus connection included, Number of actuation points 5, With LED indication, With label area, Material Metal, Material quality Stainless steel, Surface treatment Metallic, Type of surface Brilliant, Colour Stainless steel, Degree of protection (IP) IP20, Colour variant Stainless steel, Push-button, 2-gang plus metall, stainless steel For System Design. With integrated bus coupling unit. Push-button with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. Contents: With protective hood for plaster. With bus connecting terminal. Manufacturer: Merten Color: stainless steel Manufacturer-No.: 628146 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 628146

EAN: 4042811029814 - manufacturer-number: 628219 - Touch sensor for bus system 7-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 7, With LED indication, With label area, Material Plastic, Material quality Thermoplastic, Surface treatment Untreated, Type of surface Brilliant, Colour White, RAL-number (akin) 9010, Degree of protection (IP) IP20, Colour variant Polar white, Push-button, 3-gang plus Thermoplastic, brilliant, polar white For System Design. With integrated bus coupling unit. Push-button with six operating buttons, operating display, six blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. Contents: With protective hood for plaster. With bus connecting terminal. Maunufacturer: Merten Color: polar white Manufacturer- No.: 628219 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 628219

EAN: 4042811049010 - manufacturer-number: 628246 - Touch sensor for bus system 7-fold Bus system EIB/KNX, Other bus systems None, Mounting method Flush mounted (plaster), Number of actuation points 7, With LED indication, With label area, Material Metal, Material quality Stainless steel, Surface treatment Metallic, Type of surface Brilliant, Colour Stainless steel, Degree of protection (IP) IP20, Colour variant Stainless steel, Push-button, 3-gang plus metall, stainless steel For System Design. With integrated bus coupling unit. Push-button with six operating buttons, operating display, six blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single pushbuttons. The device is connected to the bus line with a bus connecting terminal. INSTABUS EIB software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger 1-, 2-, 4- or 8-bit telegrams (distinction between short and long operation), pulse edges with 2-byte telegrams (distinction between short and long operation), 8-bit linear regulator, scene retrieval, scene saving, disable functions. Contents: With protective hood for plaster. With bus connecting terminal. Maunufacturer: Merten Color: stainless steel Manufacturer- No.: 628246 Note:After registration and login, all costs (also discounts) arising for you will be clearly shown in the cart (over the icon cart) depending on the payment methods, shipping methods and order amounts you have selected as well as your country and address. - 628246